Announcement

Collapse
No announcement yet.

What I have been working on

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • I had Diablo Rojo "Matt" at Powder Works and his guys powder coat some of my rear end parts. I should have had him do the entire rear end housing...

    They did the caliper mounting brackets, anti-moan plates, tension rods and the rear end cover. Their red matched the other red suspension parts perfectly.

    I can't wait to get this thing together and up in the car.





    Fuck you. We're going to Costco.

    Comment


    • Paul (greenbullet) came over and assembled the rear and we got it in the car along with the transmission.

      I have to go through all the suspension and tighten the bolts and set the instant center and ride height. Still lots of work to do but this was the hard stuff getting the rear and trans up in there.



      Fuck you. We're going to Costco.

      Comment


      • Looks fuckin tits man
        Putting warheads on foreheads since 2004

        Pro-Touring Build

        Comment


        • That looks badass.
          01 red GT - 745whp/780wtq Whippled 4V and built 4R75W

          Comment


          • Front struts arrived. Too bad I leave tomorrow morning.

            Fuck you. We're going to Costco.

            Comment


            • Those look nice!

              Comment


              • Originally posted by Mysticcobrakilla View Post
                Those look nice!
                Phenomenal quality. Only small gripe is that they do not come with new nyloc nuts for the strut top. Not a big deal, probably cost me $1.50 for 2 but I'll hand carry one into Ace Hardware to verify the threads since I don't have a nut in my bin that matches.
                Fuck you. We're going to Costco.

                Comment


                • I'm gonna have to look into them. I know jack shit about Viking.

                  Comment


                  • Send them to me for testing

                    Comment


                    • We put the coil overs and LCAs on Mike's car, we got it at around a 26"-27" ride height and it handles like it is on rails already. Panhard bar goes on this weekend. Torque arm will be later once he gets some subframes.

                      That Viking stuff looks nice, man.
                      Originally posted by racrguy
                      What's your beef with NPR, because their listeners are typically more informed than others?
                      Originally posted by racrguy
                      Voting is a constitutional right, overthrowing the government isn't.

                      Comment


                      • Originally posted by Broncojohnny View Post
                        We put the coil overs and LCAs on Mike's car, we got it at around a 26"-27" ride height and it handles like it is on rails already. Panhard bar goes on this weekend. Torque arm will be later once he gets some subframes.

                        That Viking stuff looks nice, man.
                        Glad to hear. PM me if you guys have any questions on the PHB.
                        Fuck you. We're going to Costco.

                        Comment


                        • Originally posted by Sleeper View Post
                          Send them to me for testing
                          Damn. Too late. Already in the car.


                          Had to carry one into the hardware store to get the thread size for the top mount. Good thing, damn thing is an M16-2.00.

                          Not sure how this is going to work out once everything is right asnd aligned. Sure looks close to the away bar links.



                          Fuck you. We're going to Costco.

                          Comment


                          • I run the same coil overs Viking is good shit
                            2003 oxford white cobra whipple powered corn fed
                            2018 F150 RCSB 5.0

                            Comment


                            • Originally posted by terminator03 View Post
                              I run the same coil overs Viking is good shit
                              Any problems with them clearing the sway bar links?
                              Fuck you. We're going to Costco.

                              Comment


                              • Shorter stay bar links lol.

                                Comment

                                Working...
                                X