Shopping metal building contractors

[HarrisonTX]

Good thread.
I'm about ready for a change in a year or so.

My big decision is this.
I have a 1 acre plot on 377 south of fort worth. The good news is its paid off, the bad news is there's building regulations. Minimum 2k sq/ft, brick home with x% of stone work, garage not facing the street...etc.

or

sell that land (+/- $40k)

buy 2-3 acres somewhere else and build something VERY similar to whats pictured below.
I want to live in a metal building more than a 2k sq/ft house. Problem is 2-3 acres is so fucking expensive anywhere thats remotely close to DFW (im looking south of i-20 between benbrook and mansfield) and I have a slight emotional attachment to that 1 acre lot on 377.

[Baron Von Crowder]

I think the building I will be choosing will be a trussed 30x40x14 with a 10' awning on the 40' side. It was quoted with one door and a 4" w/beams slab for 21,650. Id like another door and a 6" concrete, at least in the shop part.

Edit: final quote after looking at options is a 12x12 door, 6" concrete, insulated roof and a double walk in door, comes to $23,324 turn key.

[KBScobravert]

I'm interested in hearing the final quote.

When I get home next week we are meeting a couple contractors who have built additions in our hood. Looking at closing in my 1car garage bay and adding a 2 car additionally to the side of the house. The original 1car bay will get a window and man door entrance and be turned into a gym/lounge. The 2 car addition will be roughly 25' wide and 35'+ deep with another man door and some windows to break up the long solid wall and bring in natural light.

Sent from my SM-G955U using Tapatalk

[hotrod66stang]

Thanks. I'll post updates once I receive an additional quote.

[fordracing19]

14ft is plenty. You can also go up on roof pitch. I went with a 10ft awning and it is too narrow. I would do 15ft. Tr built mine 5 years ago and I have no complaints.

[hotrod66stang]

*tl;dr:
Extend the slab 10' x L to have ability to leave truck/trailer inside, or extend ~12' x W and build lean-to on side? Pick one.

Is 14' wall height tall enough to have a decent upstairs storage area?

How much extra $ to plumb in pipes that I can connect to later on for water/wastewater/run elec through?

How much do I save by building my own pad and digging footers/beams and water/elec runs?



I know some of these are best answered by the builders themselves, but I'd like to see if any of you have had your bid broken down by each item, or been quoted a price for adding things to your build.

I'm looking to go as large as 50'x60' with an additional lean-to (and concrete) for my trailers on one side, and about a 15' covered porch in front.

So, first things first. Let's discuss dimensions. I've always heard that you should go as big as you can afford, because you will fill up the shop. I initially wanted to switch from 40' deep x 60' wide to 50' deep x 60' wide so that I could just pull into the shop with a trailer hooked up and leave it, if need be. 40' would be cutting it extremely close, and the extra 600 sq. ft. wouldn't hurt. So would YOU rather have the extra 10' of depth, or a lean-to on the side for trailer storage, if you had to choose one or the other? Ideally, I'll get both.

Height. I asked for a quote for a side-wall height of 14'. It should be MUCH cheaper to go up, than to go out due to the price of concrete. I'm putting in a lift, and I would like to build a loft area for storage later on, with a nice workspace underneath. Is 14' enough? 7' tall in the workspace, 1' tall between I-beam and decking, leaving 6' at the wall, with more room away from the wall with the slope of the roof.

How much extra is it for these guys to at least plumb in pipes for water/wastewater/electric runs?

Lastly, I have a 45hp tractor with FEL and backhoe. I could always do my own pad and trenches for water/elec, but I've read that certain builders won't install a building on a pad they didn't prepare. Obviously, only the builder can answer if they would allow it, but how much could I potentially save since that cost is rolled into the building?

Is there anything else that I need to consider, or any pro-tips you have for shop design/layout? I'll try to update this thread later today with a sketch of what I'm looking at building.

[hotrod66stang]

I just contacted to T.R. to get a quote last night. Mark got right back to me to get some additional info on whether or not I live in the city limits. He e-mailed me back with a quote. Unfortunately, I used the "leave a message" tool on their website, so I didn't go too in-depth with my plans. For reference, here is the gist of what I requested:
Quote for a 40'x60' or 50'x60'x14'
6" slab
insulation
3 roll-up doors

The quote I received was:
40'x60'x14'
6" slab
foam insulation
(1) 3'x7' door
(3) 10'x10' roll-up doors
$48,000

I know these guys are busy, so I'd rather have my options narrowed down a little bit before I start the "back-and-forth" process of pricing additions of concrete, lean-to's, etc.. That's where I need some help from those of you that have built shops already, or have gotten a quote for your specific building you've planned. Also, I'm pretty sure their prices went up on their website, so if this looks a little high compared to what you got, please let me know.

See next post for tl;dr and questions.

[HenryJ]

Definitely get a quote from Hot Rod Welding @ 940-577-0707. He built my 40X60 and I have no complaints with the work they did. If you're interested in checking it out let me know, I live in the Keller area.

[Baron Von Crowder]

and now I am looking at building a 30x40.

[lowfast]

Has anyone ever erected one of these them self? If I had my general contractor for the house take care of the slab is this something that you can do yourself or is it best left to the professionals?

[lowfast]

I am about 6 months out from the build, but I am a person who needs to plan things in advance, I call it being particular, my wife says anal retentive.

I would like to get a quote from them based on my needs and then know what I need to budget for the project. This will be built in conjunction with our new house so a bit more coordination is required than just a normal "build it in the backyard" scenario.

[STANGGT40]

I think I loaded a few. I'll take some of the finished product and inside...I thought I had more, but I can't find them.

Edit...well that didn't work out...it loads one and won't load the others...

[STANGGT40]

Any ideas on how to get TR Metal Buildings to respond. Sent a few emails and placed a few calls. Finally heard back and he ask me to send him the drawings I had of the layout I wanted, now a month later and still no response. People seem satisfied with their work, but can't have them build if I can't get a hold of them.

They're good, so they stay busy. When they're overly busy, their responsiveness seems to decrease substantially. I had the best luck calling mark, fwiw.

[STANGGT40]

I'd be really interested to see these pics when you get them. I'm thinking about doing a 40x60 myself.

I'll post some up this evening...I can't seem to figure out how to post them from my phone.

[lowfast]

Thanks