Announcement

Collapse
No announcement yet.

Pictures of your work?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Sgt Beavis
    replied
    Originally posted by HarrisonTX View Post
    Killer huey pics man. I never got to ride in one. Countless blackhawk and chinhook missions but I only even saw a huey in flight once.
    Yea, Desert Storm was the last time they saw any significant action.

    Leave a comment:


  • inline 6
    replied
    Speaking of huey.... When I was in San fran last month working this was in the same hangar.







    And so were these.....







    Last edited by inline 6; 02-01-2014, 09:43 PM.

    Leave a comment:


  • HarrisonTX
    replied
    Killer huey pics man. I never got to ride in one. Countless blackhawk and chinhook missions but I only even saw a huey in flight once.

    Leave a comment:


  • turboford
    replied
    Pictures of your work?

    Damn I can't get the pic to load right.

    Leave a comment:


  • Sgt Beavis
    replied
    How about my workplace from Ye Olden Tymes...

    Some shots from Camp Zama Japan..









    Flying over Virginia


    My crew of misfits..


    Promotion to Sgt


    Running around the Munchkin Land Military Ball.. Seriously damn midgets everywhere in this unit..

    Leave a comment:


  • HarrisonTX
    replied
    I made room for you, come on in.

    Leave a comment:


  • Andy@PrimeTuning
    replied
    Tried to send a PM - Box is Full

    Leave a comment:


  • HarrisonTX
    replied
    Originally posted by Andy@PrimeTuning View Post
    I see you are at SPM

    I hope you design works great and they send you around to all locations building one.
    I work for a contractor. We've been out there for three years now almost daily.
    They only have three of these. 2 here and one in Houston. I may be retrofitting the other two, but that's it.

    Leave a comment:


  • Andy@PrimeTuning
    replied
    I see you are at SPM

    I hope you design works great and they send you around to all locations building one.

    Leave a comment:


  • HarrisonTX
    replied
    This is my first PLC job since school.
    It's for a heat treating and coating process of a plunger for frac pumps.
    The part is heated to 400F, coated, and then heated to 1400F. Originally a guy stood there holding two torches while the the part turned on the lathe. It was hot work for the guy. The maintenance men mounted these limit switches and I did the rest.

    A torch now is mounted to that square piece of steel and upon selecting "run" the torch will leave the first limit switch and bounce back and fourth between the 2nd and 3rd limit switch until the desired heat is achieved. Initially it sounded pretty simple but for a bit complicated faily quickly.
    I added a DC controller and a pot to control the speed of the torch.
    I built in a couple safties too. For example, the lathe cannot drop the part with it's running, yada yada yada.
    Pretty rewarding adventure when all was said and done.
    [the incoming wires are temped in]



    Leave a comment:


  • diablo rojo
    replied

    Leave a comment:


  • Mysticcobrakilla
    replied
    Originally posted by Strychnine View Post
    3508?
    Yes sir!

    Leave a comment:


  • Strychnine
    replied
    Originally posted by mysticcobrakilla View Post
    just finished this pos!
    3508?

    Leave a comment:


  • Mysticcobrakilla
    replied
    Just finished this POS!

    Leave a comment:


  • tribaltalon
    replied
    Man those smittybilt armor fenders are getting so overdone on JK's these days.

    Leave a comment:

Working...
X